Zanussi DCS 14 S Instrukcja Użytkownika

SMART ELECTRONICSSMART ELECTRONICSHD Cabinets and CountersHD Cabinets and CountersTrainer: Lorenzo GiustiCustomer Support Refrigeration Platform

10Category Type food Temperature Umidity5 Drinks 8°C-2°C75%0°C90%90%75%4°C6°C 90%1White & game meat2 Pork & Beef meat3 Cheese,salted meat4 Veg

11Set the Food CategorySet the Food Category((FREEZERFREEZER))ADVANTAGE FOR THE CHEF MANAGER:Humidity & temperature are locked at the optimal cond

12How to set the category WHAT TO DO:Keep pressed and select category up or downDisplay shows, for each category, the stora

13The new food category will be memorized automaticaly if button is not pressed for 5 seconds.In the display will be visualized in the left side the

14SMART DEFROSTWith the new electronic control the defrosting cycles are made only when it is necessary (it is an Electrolux patent); this means that

15OBJ: 24 hrs. per day temperature monitoring andrecord keeping of the temperature over the critical limitALARM CONDITIONS:-the display shows an alar

16HOW TO CHECK IT?In the display rolling the label i.e. TEMP +14°C1. Press the button and the buzzer switch OFF2. Press the button an

17HOW TO CHECK IT?When the alarm has occurred the display shows the label TEMP Critical temperature14°C10°C5°Cset point temp.time16.00 17.00 18.00 1

18ProbesThe unit with the new electronic control is supplied with 4 probes:“S” - Storage probe: measuring inner temperature“E” - Evaporator probe: mea

19How to check temperature Probes1. Pressing the following buttons together you may see the value of the temperature of the first probe1. Pressing t

21. Temperature setting 2. Manual defrostHigh Humidity -led ON (90%)Low Humidity -led OFF (75%)Food category: automatic set of the optimal temperature

20Where you can find Them?i.e. CabinetInside the cellInside the cell(right side)(right side)Inside of EvaporatorInside of Evaporator(to defrost)(to de

21Where you can find Them?In front of condenserIn front of condenser(by ventilation)(by ventilation)Room probeIn the right side of CondenserIn the rig

22Which type of probes are used in the smart electronic?Condenser/room probe temperatureCondenser/room probe temperature1.1.NTC Semitec 10 K 25°CNTC S

23Which type of probes are used in the smart electronic?Evaporator probe temperatureEvaporator probe temperature1.1.NTC 10 K SMDNTC 10 K SMD2.2.Range

24The following parameters are kept and recorded, for 7 days:& Performance (CAP)”Coefficent appliance’s Performance”& Min and Max “Cell” tempe

25What’s means (CAP)?CAP (COEFFICENT APPLIANCE’S PERFORMANCE)The CAP is a qualitative evaluationregarding the utilisation of the appliance. It is base

26How can you check theseven days historyTo check out the the history parameters,1. Press the buttons together for 3 second and the display will show

27Programming ParametersThe Electronic board allows the adjustment of 94 parameters, through two Programming routines.1. We have 17 USER PARAMETERS,

28Programming ParametersUser parameters1) To have access to the USER PARAMETERS press the buttons increase & decrease for 4 seconds.Now the displ

295 PROGRAMMING PARAMETERS Name Setting the real time MIN Set the time: minute. HOUR Set the time: hour. DAY Set the date: day. MON Set the date

31. Temperature setting 2. Manual defrostFood category: automatic set of the optimal temperature & humidity for each kind of food1. To check alarm

30Name Alarms CDIF Alarm temperature type for cell “A”= absolute “r”= relative (compared to set point) HAL High temperature alarm for cell. LAL Low t

315 PROGRAMMING PARAMETERSName Display and Printer FHUM Humidity setting. “Enable and disable the humidity button” DIR Display resolution. “Full

325 PROGRAMMING PARAMETERSName Printer TPRN Printing interval time PRND Enable short daily report. “Y”= print only alarms “N”= print temperature cel

331) To have access into the FACTORY PARAMETERS press the buttons increase & decrease for 4 seconds.Now the display visualizes the time and the da

34 Name SET POINT Setting DIFP Positive differential (re-start compressor). Set +DIFP DIF- Negative differential (stop compressor). Set - DIF HSP H

35Name Alarm setting ADI Alarm differential “High /low temperature” ADY Alarm delay. “High /low temperature” AOR Alarm time after power on. DOT Doo

365 PROGRAMMING PARAMETERSName Defrost HTC High temperature of condenser. “alarm” DCS Defrosting counting system. ABS= absolute time HCP= working ho

375 PROGRAMMING PARAMETERSName Defrost DOD Defrost delay at power on. DIN Defrost interval between two defrosting cycles.DTO Defrost timeout. DST Defr

385 PROGRAMMING PARAMETERSName Defrost DRT Drainage time. TDF Evaporator fan temperature delay to start. CETO Timeout for evaporator fan after defro

395 PROGRAMMING PARAMETERSName Other parameters UNI Measure Unit “C= Celsius degrees” “F= Fahrenheit degrees” P4T Enable printing temperature of all

4Where can You find IT?Where can You find IT?In the HEAVY DUTY Cabinet one door and two doors.Lift up the control panel and remove the back protection

405 PROGRAMMING PARAMETERSName Other parameter TROO Room sensor type. Nus= not used; NTC2= 10K sensor; NTC3= 10K sensor (SEMITEC) TCND Condenser sen

41O To have acces into the SERVICE ALARM press the button for 4 seconds.O Now the display visualizes the first SERVICE ALARM memorized in the electro

426 ALARMLABEL TYPE ACTION DOOR OPEN Check the door HACCP alarm full Reset history memory High temp. condenser Check the condenser if is dirty o

43Service alarm Type “E” S_SC (storage sensor) “Sensor short-circuited.” S_OP (storage sensor) “Sensor is broken or disconnected.” E_SC (evaporato

44

5Where can You find IT?Where can You find IT?In the HEAVY DUTY Counter freezer and refrigeratedExtract the control panel from table and remove the up

6DESCRIPTION OF MAIN BOARDDESCRIPTION OF MAIN BOARDJ3J8J2J1(1 – 2)...J4J7J1(3 – 4)

7Description of the connectorsDescription of the connectorsPosition DescriptionJ1 POS. 1-2CONDENSER PROBE CONNECTOR type LUMBERG 2.5 MSF 4J1 POS. 3-4A

8I.E. Electric diagram

9MANUAL Setting Temperature MANUAL Setting Temperature 1. Press the button ON/OFF for 3 seconds.Now all of the led in the electronic board are blinkin