Zanussi ZDF6745 Instrukcja Użytkownika

User manualDishwasherZDF 6745

Water hardness Adjusting the water hardnesssettingUse of salt°dH °TH mmol/l manually electronically11 - 14 19 - 25 1,9 - 2,5 1 level 3 yes4 - 10 7 - 1

3.Press function button A, the lights of func-tion buttons B and C turn off while the lightof function button A goes on flashing. In thedigital displa

IMPORTANT!Top up the special salt when the light on thecontrol panel illuminates.Filling with rinse aidOpen the lid.Fill up with rinse aid. Themaximum

Open the lid. Set the dosage level. (Thedose is factory set in po-sition 4).Close the lid and press un-til it locks.Loading cutlery and dishesSponges,

For washing in the dishwasher the following cutlery and dishesare not suitable: are of limited suitability:• Cutlery with wooden, horn, china or mothe

Load cutlery. For best re-sults we recommend youto use the cutlery grid pro-vided (if the size and di-mensions of the cutleryallow it)Place knives and

Maximum height of the dishes in : upper basket lower basketWith upper basket raised 20 cm 31 cmWith upper basket lowered 24 cm 27 cmTo move to the hi

Open the lid.Fill in the detergent incompartment A.Observe the dosing lev-els.For programmes with pre-wash add an additionaldetergent dose in com-part

Once this function is selected it will remain ac-tive also for the following washing programmes.With the selection of this function the inflow ofrinse

Unloading the dishwasher• Hot dishes are sensitive to knocks.The dishes should therefore be allowed tocool down before removing from the appli-ance.•

Thank you for selecting ourapplianceWe wish you lots of enjoyment with your newappliance and we hope that you will considerour brand again when purcha

Put the flat filter A back inthe base of the washingcompartment and ensurethat it fits perfectly underthe two guidesD.Replace the filters andlock by t

3. Remove the water inlet and discharge ho-ses.4. Pull the machine out together with the ho-ses.Avoid over tilting the machine during transpor-tation.

Fault code and malfunction Possible cause and solution appears in the digital display.The dishwasher does not fill with water.• The water tap is block

The wash results are not satisfactoryThe dishes are not clean • The wrong washing programme has been selected.• The dishes are arranged in such a way

Noise level dB(A) 47Consumption valuesThe consumption values are intended as aguide and depends on the pressure and thetemperature of the water and al

Full load: 12 standard place settingsRinse aid setting position 4 (Type III)Upper basketCutlery basket Lower basketcup racks: position AInstallation

Water inlet hose with safetyvalveConnect the inlet hose to a water tap with anexternal thread of 3/4”.After connecting the double-walled water inletho

be no smaller than the diameter of the hoseprovided.Electrical connection CAUTION!Safety standards require the appliance to beearthed.Prior to using

www.electrolux.com156992070-00-29082007Subject to change without notice

Safety informationIn the interest of your safety and to ensure thecorrect use, before installing and first using theappliance, read this user manual c

Installation• Check your dishwasher for any transportdamage. Never connect a damaged ma-chine. If your dishwasher is damaged con-tact your supplier.•

1On/Off button2 Programme selection buttons3Delay start button4 Indicator lights5Digital display6 Function buttonsSetting modeIMPORTANT!Always remembe

Programme selection buttons•Starting the washing programme:1. Press the On/Off button.2. Press the button corresponding to the requiredprogramme, the

Delay start buttonThis option allows the start of the programme to bedelayed from 1 to 19 hours. After having selected thewashing programme press the

Washing programmesProgramme Degree of soil Type of load Programme descriptionIntensive 70°Heavy soil Crockery, cutlery, potsand pansPrewashMain wash2

the stated range for "Auto" programme (see"Washing programmes chart").During the "Auto" programme the temperatureof the